 |
胶水公司
| 联系人：王小姐
女士 (主管) |
| 电 话：021-51693135 |
手 机：13052326431  |
 |
|
 |
|
| HYSOL PC62电子组装/工业胶水/电子组装胶水/工业用胶 |
HYSOL PC62电子组装/工业胶水/电子组装胶水/工业用胶
技术服务热线：021-51693135 / 021-22818476
PC62 conformal coating is a rapid drying acrylic for circuit board protection.
TYPICAL PROPERTIES OF UNDRIED MATERIAL Viscosity, Brookfield - LV, 25 °C, cps:Spindle 1, speed 30 rpm 40 to 65Specific Gravity @ 25oC 0.81 to 0.83Tack Free Time:~25°C/~35% RH (120μm wet film), minutes <5Flash Point - See MSDSTYPICAL DRYING PERFORMANCE Recommended Drying Conditions24 hours @ 25°CAlternative Drying Conditions45 minutes @ 75°CDrying of the coating depends upon solvent evaporation.
For optimum performance, boards should be dried at least 30 minutes at 25°C to remove solvents before final drying in oven (or before applying additional coats).
Drying temperatures higher than recommended could cause formation of bubbles if bulk solvent is not allowed to evaporate before placing in oven.
Optimization of the drying schedule may be possible to reduce the times stated above. Ultimately, drying times will depend on film thickness and circuit board design.
It is therefore imperative to verify the drying schedule for each applications.
Desecration is not suggested due to a risk of solvent lossSTORAGEStore product in the unopened container in a dry location. Storage information is indicated on the product containerlabeling.
Optimal Storage: 5°C to 30°C. Storage below 5°C or greater than 30°C can adversely affect product properties.
PC62保形涂层是用于电路板保护的快速干燥丙烯酸
物理性质：Brookfield-LV，25℃，cps：主轴1，速度30rpm 40至65特定重力@ 25℃0.81至0.83释放时间：〜25° C /〜35％RH（120μm湿膜），分钟<5闪点 - 参见MSDSTYPICAL DRYING PERFORMANCER推荐的干燥条件24小时25°CA替代品干燥条件75分钟@ 75°涂层取决于溶剂蒸发。对于*佳性能，板应在25°C下干燥至少30分钟，以在*后干燥之前（或在施加额外的涂层之前）除去溶剂。如果散装溶剂在放入烘箱之前不允许散装，则高于推荐的温度会导致气泡的形成。干燥时间的优化可以减少上述时间。
*后，干燥时间取决于膜厚度和电路板设计。
因此，必须验证每个应用程序的干燥时间表。
由于存在溶剂损失的风险，因此不清洁脱水STORAGE Store产品在未开封的容器中，在干燥的位置。储存信息在产 |
 |
| |
|
|
 |
|
|
免责声明：以上所展示的信息由会员自行提供，内容的真实性、准确性和合法性由发布会员负责，www.qy6.com对此不承担任何责任。如有侵犯您的权益，请来信通知删除。